Here’s a clean, professional write-up for the USB device with VID 1E3D and PID 198A, incorporating “TOP” as a likely product or brand identifier.
The USB ID 1e3d:198a belongs to the Jio JMR1040 Data Card. It is a ubiquitous device in India for portable 4G connectivity, functioning as both a USB modem and a portable Wi-Fi router.
The USB hardware ID VID 1e3d PID 198a identifies a generic Flash Disk manufactured by Chipsbank Microelectronics Co., Ltd
. These IDs are often associated with low-cost or "no-name" USB drives, as well as some counterfeit storage devices sold on marketplaces like AliExpress. Technical Device Breakdown Vendor (VID): — Chipsbank Microelectronics Co., Ltd. Product (PID): — Flash Disk / ChipsBnk Flash Reader. Common Controllers: Frequently uses the Chipsbank CBM2099E controller chips. USB 2.0 (High Speed). Common Issues and Identification
This specific ID is notorious in tech support forums for appearing on drives that have "failed" or were manufactured with "fake" capacities. "No Media" Error:
Users often report that the computer recognizes the device (the "ChipsBnk" controller) but shows "No Media" or a capacity of
. This typically indicates a communication failure between the controller chip and the flash memory chip. Fake Capacity Warnings:
Some "16TB" or "2TB" SSDs/thumb drives from discount sites use this Chipsbank ID to trick the OS into reporting a high capacity, while the actual physical storage is much lower (e.g., 32GB or 64GB). Device Recognition: In Linux, it usually appears in ID 1e3d:198a Chipsbank Microelectronics Co., Ltd Flash Disk Troubleshooting and Recovery Steps
If your device is showing this ID but isn't working correctly, you can try the following: Identify Real Specs: Use tools like ChipGenius Flash Drive Information Extractor (usbflashinfo) to get the exact controller part number and Flash ID. Controller-Specific Tools:
If the drive is non-functional but detected, you may need a "Mass Production Tool" (MPTool) specific to the Chipsbank CBM2099/2199 series to re-initialize the controller. Check for Counterfeits: (Windows) or
(Linux/Mac) to test the actual storage capacity. If the test fails early, the drive's advertised capacity is likely fake. Hardware Test Mode:
For advanced users, some forum guides suggest putting the chip into "test mode" by shorting specific pins on the controller to force the computer to recognize it as a generic bootable device for firmware reflashing.
Using mass production tools or shorting pins often results in complete data loss. If you need the data, consult a professional recovery service before attempting firmware fixes. Are you trying to recover data from a drive with this ID, or are you looking for the firmware/drivers to fix a "No Media" error? USB\VID_1E3D = Chipsbank Microelectronics Co., Ltd
The USB identifiers VID 1e3d and PID 198a identify a generic Flash Disk manufactured by Chipsbank Microelectronics Co., Ltd.. These IDs are often associated with low-cost or unbranded USB flash drives and SD card readers that utilize Chipsbank controllers. Device Specifications
Based on hardware databases and technical logs, here are the common properties for this specific identifier:
Manufacturer (Vendor ID 1E3D): Chipsbank Microelectronics Co., Ltd..
Product (Product ID 198A): Recognized as a Flash Disk or "Flash Reader". Controller Model: Often uses the CBM2199S controller chip.
Protocol: Generally operates on the USB 2.0 protocol at High Speed. Power Consumption: Typically draws around 100mA. Driver & Troubleshooting
This device is a standard "Mass Storage Class" device, meaning it should not require specialized drivers for modern operating systems like Windows 10/11, macOS, or Linux. usb device id vid 1e3d pid 198a top
Recognition Issues: If the device appears as an "Unknown Device" in Windows Device Manager, it may be due to a faulty controller or corrupted partition. You can verify the hardware ID by right-clicking the device, selecting Properties > Details, and choosing Hardware Ids from the dropdown.
Speed & Performance: Users have noted that drives with these IDs are often budget-tier and may show varying performance in USB Flash Drive Speed Tests.
Linux Logs: In Linux, the device will typically be logged as idVendor=1e3d, idProduct=198a using the xhci_hcd or ehci-pci drivers. Warning: Counterfeit Capacities
Chipsbank controllers are frequently found in generic USB drives. If you find that this device reports a very high capacity (e.g., 2TB) at a very low price, it is likely a fake capacity drive. These drives use modified firmware to report more space than they actually have, leading to data loss once the true physical limit is reached. Tools like H2testw can verify the actual storage capacity of these devices.
Are you experiencing a specific technical error or data loss issue with this particular USB drive?
Demystifying USB ID VID 1E3D PID 198A: The Chipsbank Flash Disk
Have you ever plugged in a USB drive and found it labeled simply as "USB Mass Storage Device" or noticed a strange string of characters like VID 1E3D PID 198A in your Device Manager? Identifying these IDs is the first step toward troubleshooting a drive that won’t format or finding the right mass production tool to revive a "dead" stick. What is VID 1E3D PID 198A?
Every USB device uses a Vendor ID (VID) and a Product ID (PID) to identify itself to your operating system. For this specific combination:
VID 1E3D: This identifies the manufacturer as Chipsbank Microelectronics Co., Ltd. PID 198A: This identifies the specific product as a Chipsbank Flash Disk .
This ID is commonly associated with budget-friendly flash drives or unbranded "no-name" sticks that use the Chipsbank CBM2199E or controller. Technical Specifications
According to data from ChipGenius and other diagnostic tools, these devices typically feature: Protocol: USB 2.00.
Speed: High Speed (theoretical max of 480 Mbps), though real-world write speeds often hover between 3–17 MB/sec. Current Draw: Max 100mA.
Flash Memory: Often paired with Micron TLC or MLC memory chips. Common Uses and Issues
Because these controllers are inexpensive, they are frequently used in promotional USB drives or even "fake" high-capacity drives (where the reported size is larger than the actual storage). Common Problems:
"No Media" Errors: The drive appears in Disk Management but shows no storage capacity.
Write Protection: The drive becomes read-only and cannot be formatted by standard Windows tools.
Firmware Corruption: The device is recognized by the PC but won't open or show up in File Explorer. How to Fix or Manage This Device
If you're having trouble with a VID 1E3D PID 198A drive, you may need specialized Chipsbank USB tools like APTool or UMPTool. These utilities are designed for low-level formatting and firmware reflashing. For standard troubleshooting, you can try: Here’s a clean, professional write-up for the USB
The USB device identified by VID 1E3D and PID 198A is a mass storage device utilizing a controller from Chipsbank Microelectronics Co., Ltd.. This specific hardware ID is commonly associated with budget or "no-name" USB flash drives, often sold as promotional items or through online marketplaces like AliExpress. Technical Specifications Manufacturer: Chipsbank Microelectronics Co., Ltd.
Controller Models: Frequently uses CBM2199 series chips (including CBM2199S, CBM2199E, or CBM2199A). Protocol: USB 2.0 (High Speed).
Performance: Performance varies significantly by the flash memory paired with the controller:
Read Speeds: Typically range from 10 MB/s to 45 MB/s depending on drive capacity. Max Current: 100mA. Performance & Reliability Review Chipsbank Microelectronics Co. Ltd - USBDev.ru
The USB device with generic flash drive manufactured by Chipsbank Microelectronics Co., Ltd
. This specific ID combination is frequently found in high-capacity but low-cost USB drives, often sold on marketplaces like AliExpress. devicehunt.com 📋 Technical Device Profile Manufacturer (VID): Chipsbank Microelectronics Co., Ltd. (1e3d) Product (PID): Flash Disk / UDisk (198a) Typical Controller: USB 2.0 (High Speed) Current Draw: Typically 100mA devicehunt.com ⚠️ Common Usage & Risks
Devices using this ID are often flagged in the tech community for quality and authenticity issues: Fake Capacity:
This controller is commonly used in "fake" drives that report a high capacity (e.g., 64GB, 2TB, 16TB) but only contain a fraction of that storage. Data Corruption:
When the real storage limit is hit, the drive may continue to "accept" files by overwriting old data, leading to total data loss. Read/Write Speeds:
Performance is generally low, often inconsistent with modern USB 3.0 standards despite being marketed as such. superuser.com 🛠️ Troubleshooting & Recovery
If your device is failing or showing incorrect capacity, the following steps are standard for Chipsbank controllers: Identification: Use tools like ChipGenius Flash Drive Information Extractor to confirm the specific controller model (e.g., CBM2199E). Repair Tools: CBM2099 UMPTool
are often used to re-flash the firmware or "reset" the drive to its actual hardware capacity. Hardware Reset:
In extreme cases where the drive is not recognized, some users manually short pins 29 and 30 on the controller to enter "Test Mode". superuser.com Recommendation:
If you have critical data on this drive, back it up immediately. These generic Chipsbank drives are prone to sudden hardware failure and should not be used for primary storage. How would you like to proceed? specific firmware tool for your controller version or provide steps to verify the true capacity of your drive. Chipsbank Microelectronics Co. Ltd - USBDev.ru
The USB device with generic flash drive controller manufactured by Chipsbank Microelectronics Co., Ltd
. These identifiers typically correspond to high-speed USB 2.0 mass storage devices, often using the controller series. www.reddit.com
This guide covers identification, common issues (like "fake capacity" or "no media" errors), and repair tools. 1. Device Specifications Manufacturer (VID 1e3d): Chipsbank Microelectronics Product (PID 198a): Flash Disk / Mass Storage Device Common Controllers: CBM2199E, CBM2199S, or CBM209x series. USB 2.0 (High Speed). 2. Common Scenarios & Troubleshooting
This specific VID/PID is frequently found in budget or unbranded "no-name" flash drives, sometimes used in counterfeit devices that report fake storage capacities (e.g., a 32GB drive that only has 8GB of actual NAND memory). www.reddit.com Potential Cause Recommended Action No Media / 0 Bytes Firmware corruption or partition table error. Use a low-level format tool specific to Chipsbank. Write Protected Comparison & Alternatives
The controller has locked the NAND to prevent further data loss. Flash the firmware using the APTool or UMPTool. Fake Capacity Firmware is spoofing the actual storage size. Run a test with to verify real capacity. 3. Repair & Formatting Guide
If your device is malfunctioning (showing as "Unknown Device" or "No Media"), follow these steps to attempt a recovery: Extract Detailed Hardware Info: Use a tool like ChipGenius Flash Drive Information Extractor
to confirm the specific controller part number (e.g., CBM2199E). Find the Correct Production Tool: Search for the specific controller version on sites like FlashDrive-Repair.com (often listed as Chipsbank UMPTool Low-Level Format: Open the mass production tool (UMPTool). Plug in the device; it should appear in one of the slots.
Select "Start" to perform a low-level format and re-verify the memory blocks. This will permanently erase all data. 4. Verified Drivers Generally, this device uses the standard USB Mass Storage Class driver
built into Windows, macOS, and Linux. If the device isn't recognized, it is likely a hardware or firmware failure rather than a missing driver. For legacy systems (e.g., Windows 7), generic drivers are sometimes hosted on sites like DriverScape
Is your device showing a specific error message like "Please insert a disk" or "Disk is write-protected"?
The USB device ID VID 1e3d PID 198a refers to a mass storage flash drive manufactured by Chipsbank Microelectronics Co., Ltd.. These devices are commonly budget-friendly, generic USB flash drives or "no-name" promotional sticks often used for data storage or distribution. Device Profile: Chipsbank Flash Disk Vendor: Chipsbank Microelectronics (VID 1E3D). Product ID: 198a. Controller: Typically uses the CBM2199E controller. Type: USB 2.0 Mass Storage Device.
Performance: Described as "HighSpeed" under the USB 2.0 protocol, though actual speeds depend on the specific flash memory chip paired with the Chipsbank controller. The "Chipsbank Experience": A Review
For a user, encountering this device usually means you've plugged in a generic flash drive. Based on technical databases like DeviceHunt and community reports from USBDev, here is what to expect:
Reliability: These are entry-level controllers. While functional for basic file transfers, they are frequently found in low-cost or promotional drives that may have a higher failure rate over time compared to premium brands.
Compatibility: Works natively with Windows, macOS, and Linux as a standard "USB Mass Storage Device" without needing manual driver installation.
Maintenance: If the device becomes unrecognized or shows "Write Protected," specialized tools like the Chipsbank APTool or UMPTool are often required to reflash the firmware. Troubleshooting Tips If your computer fails to recognize this device:
How do I check the PID and VID of my USB device? - Knowledge Center
On Linux (Ubuntu/Debian/Fedora), the device appears in lsusb output:
Bus 001 Device 003: ID 1e3d:198a Chicony Electronics Co., Ltd TOP
To get it working:
sudo apt install fprintd libfprint-2-tod1-goodix
sudo fprintd-enroll
The libfprint open-source driver supports this chip via the goodix or vfs0051 backend.
| Attribute | Detail |
| :--- | :--- |
| Vendor ID (VID) | 1E3D |
| Product ID (PID) | 198A |
| Manufacturer | Reliance Jio (specifically utilizing chipset technology from vendors like Spreadtrum/UNISOC). |
| Device Name | Jio JMR1040 (4G LTE Data Card) |
| Device Type | Mobile Broadband Device / USB Modem / Virtual CD-ROM |
| Interface | USB 2.0 |
This is the top trick for stubborn PID 198A devices.
The keyword "top" in your search ("...vid 1e3d pid 198a top") might refer to a few things:
If you received a "Device Descriptor Request Failed" error alongside this VID/PID, the hardware is physically damaged. No driver will fix that chip. You need a replacement device.