Nako Na-613d Disable Alarm [better] Instant
Here are a few ways to write this, depending on where you need to use the text:
Option 1: Instruction Manual Style (Step-by-Step) How to Disable the Alarm on the Nako NA-613D
- Locate the ALARM button on the front panel.
- Press the ALARM button briefly. The alarm icon should disappear from the display, indicating the alarm has been turned off.
- If the alarm is currently sounding, press any button (usually SNOOZE or ALARM) to stop the noise temporarily. To permanently disable it, slide the alarm switch to the "OFF" position.
Option 2: Short & Direct "To disable the alarm on the Nako NA-613D, press the Alarm button until the alarm icon disappears from the screen."
Option 3: Technical/Status Log "Device: Nako NA-613D. Action: Alarm function disabled."
To disable the alarm and hourly chime on the Nako NA-613D digital clock, you generally use button combinations from the home (time) screen. The clock typically features three buttons labeled S (Split/Lap), D (Start), and M (Mode). Disabling the Daily Alarm
To toggle the daily alarm on or off, perform the following in normal time mode: Action: Press and hold S, then press D once.
Indicator: Look for a bell icon or "ALM" indicator on the display. When the alarm is disabled, this icon will disappear. Disabling the Hourly Chime
If your clock beeps at the top of every hour, you can disable this signal using a similar combination: Action: Press and hold S, then press M once.
Indicator: In many versions of this model, if the days of the week (MON, TUE, etc.) are all visible at once while holding S, the chime is on. If the day flags disappear, the chime is disabled. Quick Reference for Buttons Standard Function M (Mode)
Cycles through modes (Time → Stopwatch → Alarm Set → Time Set). S (Split/Lap) Shows alarm time; used with others to toggle functions. D (Start) Shows date; used to advance numbers during setup.
If the buttons on your specific unit are not labeled, the S button is usually the lower-left or top-right (Lap), D is often the top-right or lower-right (Start), and M is the bottom-left.
Are you also looking for instructions on how to reset the time or use the stopwatch feature on this device?
To disable the alarm on your Nako NA-613D digital watch or car clock, follow these steps: Turn Off Daily Alarm : In normal time-keeping mode, press and hold the button and the button at the same time. The alarm is when the bell/alarm icon disappears from the display. Disable Hourly Chime
: To stop the watch from beeping every hour, press and hold the button and the button simultaneously. If the days of the week are visible while holding , the chime is ON; if they are not visible, it is OFF. Made-in-China.com Button Overview Nako NA-613D
(also sold as Kenko KK-613D) typically features three main control buttons:
: Cycles through stopwatch, alarm setting, and time setting modes. S (Lap/Set)
: Used to view current alarm time or select digits during adjustment. D (Start/Stop) : Used to view the date or change values when setting. How to Silence a Sounding Alarm nako na-613d disable alarm
When the alarm is actively ringing, press any button (except Snooze) to stop it completely for that day. Pressing the
button will temporarily silence it, but it will ring again in 5 minutes. device.report on your Nako clock as well?
Master Your Morning: How to Disable the Alarm on Your Nako NA-613D Go to product viewer dialog for this item. Whether you've just installed a Nako NA-613D
in your car or have one sitting on your desk, its loud morning chirp can eventually overstay its welcome. While these mini digital clocks are incredibly reliable, their multi-button interface can be a bit of a puzzle if you don’t have the manual handy.
Here is the quick guide to silencing that alarm and regaining control over your clock. The Quick Fix: Turning Off the Alarm Most Nako digital clocks, including the
, follow a standard "two-button" combination to toggle the alarm status.
Locate your buttons: You will typically see three main buttons: MODE, START/DATE, and LAP/RESET.
The Shortcut: From the normal time-display screen, press and hold the START and RESET buttons simultaneously.
Check the Icon: Look for a small bell icon or a set of signal bars (representing the alarm/chime) on the display. If the icon disappears, the alarm is now disabled. If the icon appears, the alarm is active.
Listen for the Beep: Often, the clock will give a short double-beep to confirm you’ve toggled the setting successfully. Disabling the Hourly Chime
If your clock is beeping every hour on the dot, you're dealing with the "Hourly Chime" rather than a set alarm. To disable this: Press and hold the RESET button. While holding RESET, press the MODE button.
All days of the week (usually displayed at the top) will either appear or disappear. When they are not visible, the hourly chime is off. When the Alarm is Already Ringing If you’re currently being blasted by the alarm sound:
To Snooze: Press the START button. This usually gives you a 5-minute reprieve before it rings again.
To Stop Completely: Press the RESET button. This kills the current alarm until the next scheduled time. Troubleshooting Common Issues
The Alarm Keeps Coming Back: Ensure you aren't just hitting snooze. You must use the button combination mentioned in the "Quick Fix" section above to disable it permanently.
The Screen is Fading: If the alarm sounds weak or the icons are flickering when you try to change settings, it’s likely time for a battery swap (typically a standard LR1130 or CR2032 button cell). Here are a few ways to write this,
By mastering these simple button combinations, you can ensure your Nako NA-613D only alerts you when you actually want it to!
To disable the alarm on your Nako NA-613D Go to product viewer dialog for this item.
digital watch or clock, you typically need to press a specific combination of buttons while in the normal time-display mode. Disabling the Alarm and Hourly Chime
According to manufacturer instructions found on Made-in-China, you can toggle the alarm status using the following steps:
Ensure you are in "Normal State": The screen should be showing the current time (hour, minute, second, and week).
Press Buttons "S" and "D" simultaneously: Push both the S (Start/Set) and D (Date/Adjust) buttons at the same time to choose between turning the alarm on or off.
Verify on Display: When the alarm is active, an alarm symbol (often a small bell icon) will be visible on the screen. If you have successfully disabled it, this symbol will disappear. Silencing a Ringing Alarm If the alarm is currently sounding and you want to stop it:
Stop Button: Press any button other than the designated snooze button to stop the alarm immediately.
Snooze: If your model includes a snooze function (often a top button), pressing it will typically silence the alarm for 5 minutes before it rings again. Common Button Layout for the NA-613D usually features a four-button interface often labeled as:
M (Mode): Used to cycle through time, alarm setting, and stopwatch modes.
S (Set/Select): Used to select specific digits to change or view the set alarm time.
D (Date/Adjust): Used to view the date or change numerical values.
Light/Snooze: Typically used for the backlight or temporary silence.
If you are having trouble, you can view a visual walkthrough for this specific model in this Digital Clock Time Setting Video. Radio Controlled Alarm Clock - argos-support.co.uk
The Nako NA-613D sat on the bedside table, its liquid crystal display bleeding a dull, rhythmic gray. To most, it was a five-dollar plastic relic of the nineties. To Elias, it was a heartbeat.
He didn't want to silence it because he was tired; he wanted to silence it because the person who had set it wasn't coming home to turn it off. Every morning at 6:13 AM—a digital mirror of its own model number—the alarm would pierce the silence of the room. It was a high-pitched, insistent beep-beep-beep-beep that felt like a needle threading through his grief. Locate the ALARM button on the front panel
He picked it up, his thumb tracing the worn plastic of the "Mode" button. He knew the sequence by heart, yet his hands shook. The Ritual of Silence : He pressed the
button twice. The blinking colon froze. The screen shifted from the relentless march of time to the static demand of the alarm setting. The Choice : He held the Start/Stop
) button. On the tiny screen, the small bell icon—the "Alarm On" indicator—flickered. The Severing : With one final click, the bell vanished.
The room fell into a vacuum of absolute stillness. By disabling the alarm, Elias realized he had finally stopped waiting for the morning that wouldn't come. The Nako NA-613D was now just a clock again—counting seconds that no longer led to her.
He set it back down. The digits flipped to 6:14. For the first time in months, the house was quiet, and the silence was louder than any alarm.
To disable the alarm on a Nako NA-613D digital clock, you generally need to use a specific button combination from the normal time-display mode. While this device is commonly marketed under the Nako brand, it shares the same internal module as the Kenko KK-613D and follows the same operating procedures. How to Disable the Alarm
To toggle the alarm on or off, follow these steps while the clock is in its Normal State (showing the current time): Locate the Buttons : The device typically has three main buttons labeled (Date/Adjust), and Toggle the Alarm : Press and hold the button, then simultaneously press the Check the Display : Look for the alarm symbol (often a bell icon) on the LCD. If the symbol is , the alarm is active. If the symbol is , the alarm is disabled. Made-in-China.com Stopping a Sounding Alarm If the alarm is currently ringing and you want to stop it: Stop Completely
: Press any button except for the specific Snooze function (if applicable to your specific variant).
: Some models may enter snooze mode if a specific button is pressed, causing it to ring again in 5 minutes. Reference for Other Modes Nako NA-613D Go to product viewer dialog for this item. button to cycle through its various functions: Press M once : Stopwatch mode. Press M twice : Alarm time setting mode. Press M three times
: Real-time adjustment mode (to set the current time and date). Made-in-China.com
For a visual guide on these settings, you can refer to instructional videos from sources like
What you need:
- Small Phillips screwdriver
- Tweezers
- Electrical tape (optional)
Quick guide — Disable alarm on NAKO NA-613D
Warning: disabling a smoke/CO alarm may create risk. Only disable temporarily for known false alarms (cooking, steam) and re-enable as soon as possible.
How to Disable the Alarm on Your NAKO NA-613D Timer: A Quick Guide
The NAKO NA-613D is a popular digital time switch used to automate appliances in homes and offices. While it is excellent for scheduling lights or fans to turn on and off, one common frustration users face is the audible alarm.
If your timer is beeping every time a setting changes, or if you simply want a silent operation, you likely struggled to find the specific button to stop it. The manual can be vague, and the buttons are not always intuitive.
Here is the step-by-step method to disable the alarm sound on the NAKO NA-613D.
4. Remove power (if silence fails)
- If battery-powered: twist or unclip the detector from its base and remove the batteries. Wait 30 seconds, then replace batteries and reattach.
- If hardwired with battery backup:
- Turn off the circuit breaker for that circuit.
- Twist or unclip the detector and remove backup batteries.
- Wait 30 seconds, reinsert batteries, and restore power.
- If fully hardwired and you cannot access breaker safely, call an electrician.
What you can do to get the report
If you are the owner or authorized technician:
- Check the actual device – Look for a brand name, model number (e.g., on a sticker or PCB), and manufacturer.
- Search with correct details – Try searching:
[Brand] [Model] disable alarm[Brand] [Model] user manual
- Contact the installer or manufacturer – If the system is installed in a vehicle, home, or machine, the original installer will have documentation.
- Look for common alarm disable methods (general, not model-specific):
- Use the remote / key fob
- Enter the PIN on the keypad
- Use the valet/override switch
- Disconnect backup battery then main power (if safe and legal)
- For car alarms: turn ignition on/off in a sequence
