The default administrator login for the Kyocera ECOSYS M3550idn
varies slightly depending on whether you are accessing the physical control panel or the web-based Command Center Tungsten Automation Default Credentials
For most M3550idn units that have not had their security settings manually changed, use the following: (Case-sensitive) (Case-sensitive) Tungsten Automation Alternative Credentials
If "Admin/Admin" does not work, try these common Kyocera defaults:
(The digits often match the first four numbers of the device's speed or model series). KYOCERA Document Solutions America Access Methods Command Center RX (Web Interface):
Open a web browser and enter the printer's IP address. Use the credentials above to log in as an administrator to manage network settings, address books, and device alerts. Physical Control Panel: [System Menu/Counter]
key. When prompted for a login, enter the credentials using the on-screen keyboard. KYOCERA Document Solutions America What if the password is changed?
If the default credentials fail, the password was likely changed for security. Check the Serial Number:
On newer firmware versions or after a partial reset, the default password may revert to the device's Serial Number Network Reset:
If you are locked out of the web interface but have physical access, you can sometimes reset network parameters via the System Menu to restore default access. Maintenance Mode:
A full factory reset (Maintenance Mode U021) will restore all defaults, but this will erase all saved settings , including network configurations and address books. KYOCERA Document Solutions America kyocera m3550idn default password
To avoid future lockouts, you can manage and store device information using the Kyocera Download Centre for official utility tools. Do you need the specific button sequence to perform a factory reset from the service menu?
Printer administrator default username and password - Tungsten Automation
The default username and password for the Kyocera ECOSYS M3550idn is: Username: Admin Password: Admin 🛠️ Common Variations
If the standard credentials do not work, Kyocera devices often use these factory defaults depending on the firmware version:
Capitalization Matters: Try Admin (capital "A") or admin (all lowercase) for both fields.
Model-Based: Some monochrome units use 5000 for both the login ID and password.
Device ID: Try the model number 3500 for both the ID and password. Legacy Admin: Try admin00 for both fields. 📍 How to Find Your Serial Number
Newer Kyocera firmware may require the Serial Number as the default password. You can find this in three places:
Machine Sticker: Look for a white sticker on the back or side of the printer.
Status Page: Print a "Status Page" from the device's Reports menu. The default administrator login for the Kyocera ECOSYS
Command Center: If you can access the web interface (Kyocera Command Center RX), it is usually listed on the home dashboard. 🔄 If the Password Was Changed
If none of the above work, the default password was likely changed by a previous administrator. To regain access, you have two options:
Factory Reset: You must enter the Maintenance Mode (Service Menu) to initialize the NIC or memory. This typically requires a specific key sequence (like 10871087). Note: This will wipe all network and scan settings.
Contact Support: Reach out to your local authorized Kyocera Dealer for a technician-level reset. Kyocera 2554ci/3554ci Admin Password
Managing a Kyocera ECOSYS M3550idn requires access to its administrative interface, whether you are using the physical operation panel or the web-based Command Center RX. If you are locked out or setting up a new device, knowing the factory default credentials is the first step to gaining control over network settings, user management, and maintenance. Kyocera ECOSYS M3550idn Default Admin Credentials
The default login depends on which interface you are accessing: Operation Panel (Physical Interface): User Name: 5000 Password: 5000
Note: The default login for this model generally follows the machine’s maximum printing speed (50 ppm) followed by two zeros. Command Center RX (Web Interface): User Name: Admin (Case-sensitive, capital 'A') Password: Admin (Case-sensitive, capital 'A')
Alternative: For newer firmware versions or different regional settings, try admin (lowercase) for both, or the device's Serial Number. How to Find Your Device Serial Number
If "Admin/Admin" fails, your password may be the unique serial number of the machine. You can find this in two places: Kyocera 2554ci/3554ci Admin Password
For the Kyocera ECOSYS M3550idn, the default login credentials depend on whether you are accessing the machine's physical panel or its web-based Command Center RX interface. Default Credentials Web Interface (Command Center RX): Username: Admin Open a browser and enter your printer's IP address (e
Password: Admin(Note: These are case-sensitive; the "A" must be capitalized). Physical Operation Panel (System Menu): Username: 5000
Password: 5000(The credentials for the physical panel are typically the machine's print speed followed by "00"). Accessing the Device
Find the IP Address: On the machine’s display, go to Status or Device Information to find its network IP address.
Open the Web Interface: Type the IP address (e.g., http://192.168.1.100) into a computer's web browser on the same network.
Log In: Use Admin for both fields to unlock full configuration settings. Important Security Notes Username and Passwords.xlsx - Milwaukee Office Products
Password. Model. Username. Password. FS-1370DN. FS-1370. FS-2100DN. Admin. Admin. FS-2100DN. 4000. 4000. FS-3920DN. FS-3920DN. FS- Milwaukee Office Products Kyocera 2554ci/3554ci Admin Password
http://192.168.1.100).Admin and the default password.| Field | Default Value |
|----------------|---------------------|
| Username | Admin or admin |
| Password | Admin or admin |
| Login Page | Device IP address → Command Center RX (web interface) |
⚠️ Note: Kyocera often uses no password on older firmware, but newer units or factory-reset devices typically use
Adminfor both username and password. If that fails, tryadmin(lowercase) or leave password blank.
After login, change the default password immediately:
Command Center RX → Security → User Login → Admin Password Change