Gunnebo Speedstile Fl Installation Manual ((free)) | ORIGINAL ✓ |

Installing the Gunnebo SpeedStile FL requires careful site preparation and precise alignment to ensure the security barriers function correctly. This guide provides a summary of the essential steps for installing the SpeedStile FL , including the FLS BA and EV variants. 1. Site Preparation and Foundation

The structural integrity of the installation site is the responsibility of the customer. Ensure the following before beginning:

Floor Quality: The finished floor must be flat and level within ± 5mm.

Foundation Depth: Use concrete with a minimum resistance of fckcube 30N/mm². The minimum bolting depth for anchors is 70mm.

Conduits: Run cables at least 140mm below the finished floor level, rising at least 50mm from the foundation. 2. Pedestal Positioning and Alignment

Correct alignment is critical for the system's sensors and flap leaves to operate properly.

Mark Alignment: Use a chalk line on the floor to mark the placement of the units.

Identify Units: Distinguish between Left (L), Right (R), and Center (C) cabinets to create the desired number of lanes.

Identify Master/Slave: For multiple lanes, identify Master and Slave pedestals. The Master unit typically contains the LCM02 board and a circuit breaker above the transformer.

Placement: Position units to be perfectly parallel. The Master unit should ideally be on the secure (exit) side of the lane. 3. Mechanical Installation gunnebo speedstile fl installation manual

Drill Fixing Holes: Once aligned, mark the fixing hole positions, move the units, and drill into the floor.

Anchor and Level: Reposition the units and secure them with anchors. Use shims to ensure the frame is perfectly level in both longitudinal and transverse directions.

Install Components: Attach flap leaves to the rotor drive column and install lids and covers once wiring is complete. SpeedStile FLs BA|EV - Protogetic

LAYOUT CONFIGURATION & STANDARD DIMENSIONS. Shown is the SpeedStile FLs Wide BA (square lid ends). The EV version (round lid ends) Protogetic SpeedStile

Gunnebo SpeedStile FL Installation Manual: A Comprehensive Guide

The Gunnebo SpeedStile FL is a popular access control solution used in various industries, including retail, transportation, and government. Its sleek design, high-speed capabilities, and advanced features make it an ideal choice for managing pedestrian traffic. However, to ensure a successful installation, it's essential to follow the manufacturer's guidelines and recommendations. In this article, we'll provide an in-depth look at the Gunnebo SpeedStile FL installation manual, covering the necessary steps, requirements, and best practices.

Pre-Installation Requirements

Before starting the installation process, make sure to:

1. Read the manual: Familiarize yourself with the Gunnebo SpeedStile FL installation manual, which provides detailed instructions, diagrams, and technical specifications.
2. Verify the shipment: Check the contents of the shipment against the order confirmation and ensure that all components, including the gate, control unit, and accessories, are present and undamaged.
3. Plan the installation site: Ensure the installation site meets the requirements outlined in the manual, including:
   • A flat, level surface
   • Adequate clearance for the gate's swing radius
   • Sufficient space for the control unit and any additional components
   • Compliance with local building codes and regulations
4. Gather tools and materials: Collect the necessary tools and materials, such as:
   • Power drill and bits
   • Wrenches and sockets
   • Wire strippers and connectors
   • Mounting hardware (e.g., screws, bolts)

Installation Steps

The Gunnebo SpeedStile FL installation manual provides a step-by-step guide for installing the gate, control unit, and other components. Here's an overview of the process:

1. Gate Installation:
   • Mount the gate to the floor or wall using the provided hardware
   • Ensure the gate is level and plumb
   • Connect the gate's electrical connections to the control unit
2. Control Unit Installation:
   • Mount the control unit to a wall or in a nearby cabinet
   • Connect the control unit to the gate and any additional components (e.g., sensors, readers)
   • Configure the control unit's settings and parameters
3. Sensor and Reader Installation:
   • Install sensors and readers according to the manufacturer's instructions
   • Connect sensors and readers to the control unit
4. Wiring and Cabling:
   • Route and connect wiring and cabling between components
   • Ensure all connections are secure and meet the manual's specifications

Configuration and Testing

After completing the installation, follow these steps:

1. Configure the system: Use the control unit's interface to configure settings, such as:
   • Gate speed and acceleration
   • Sensor sensitivity
   • Reader settings
2. Test the system: Perform a series of tests to ensure the system operates correctly, including:
   • Gate movement and stopping
   • Sensor detection
   • Reader communication

Maintenance and Troubleshooting

Regular maintenance and troubleshooting are essential to ensure the Gunnebo SpeedStile FL operates smoothly and efficiently. The manual provides guidance on:

1. Scheduled maintenance: Perform routine checks and maintenance tasks, such as:
   • Cleaning the gate and sensors
   • Lubricating moving parts
   • Checking electrical connections
2. Troubleshooting: Identify and resolve common issues, such as:
   • Gate malfunction
   • Sensor errors
   • Reader communication problems

Best Practices and Considerations

When installing the Gunnebo SpeedStile FL, keep in mind:

1. Compliance with regulations: Ensure the installation meets local building codes, regulations, and industry standards.
2. Safety considerations: Install the system in a way that prevents injuries or accidents, such as:
   • Providing adequate clearance for the gate's swing radius
   • Installing safety sensors and mats
3. System integration: Consider integrating the Gunnebo SpeedStile FL with other access control systems, such as:
   • Card readers
   • Biometric authentication
   • Surveillance cameras

Conclusion

Gunnebo SpeedStile FL: Essential Installation & Setup Guide The Gunnebo SpeedStile FL (Flap Leaf) is a sophisticated speed gate designed to balance security with a high-flow pedestrian aesthetic. This guide synthesizes key technical requirements and procedural steps for professional installation, ensuring operational longevity and safety. 1. Site Preparation & Structural Requirements Installing the Gunnebo SpeedStile FL requires careful site

Before unboxing the units, the installation site must meet specific structural and environmental criteria:

Foundation Integrity: The mounting surface should be a flat, level concrete base (Concrete to BS 5328:1997 type ST5) with a minimum thickness of 150mm.

Surface Tolerance: The floor must be level within +/- 5mm over the entire footprint of the SpeedStile unit.

Mounting Depth: Anchor bolts require a minimum depth of 70mm into concrete with a resistance of at least 30N/mm².

Conduit Placement: All electrical conduits must be run at least 140mm below the finished floor level (FFL) and should rise a minimum of 50mm from the foundation into the cabinet. Gunnebo SpeedStile FL

REPORT: Gunnebo SpeedStile FL Installation Manual

Subject: Overview of Installation Procedures and Technical Specifications for Gunnebo SpeedStile FL Speed Gates.

Date: October 26, 2023 Prepared By: Technical Documentation Review

---

3.1 Setting Operational Modes

| Mode | Description | Use Case | | :--- | :--- | :--- | | Locked | Flaps remain closed; passage requires valid credential. | Secure entry during business hours. | | Unlocked | Flaps remain open; acts as a free passage. | Fire evacuation or lunch breaks. | | One-Way | Entry lane unlocked, exit lane locked. | Event check-in. | | Momentary Open | Flaps open for 5 seconds after valid card, then close. | High-security anti-tailgating. | Read the manual : Familiarize yourself with the

Maintenance — the lifecycle view

The SpeedStile FL rewards attention. Scheduled inspections prevent drift: tighten anchors seasonally, inspect seals and glass for micro-movements, check sensor alignment, and replace consumables before failure. Keep motor firmware and access-control integrations updated with change control and backups.

Electrical and control integration — orderly connectivity

• Power supply: The SpeedStile FL typically requires a stable mains supply with an earth connection and appropriately rated overcurrent protection. Local codes govern conductor sizing and overcurrent devices; adhere to them and use an isolated earth where specified.
• Low-voltage wiring: Run access-control, sensor, and communication cables in dedicated conduits. Label both ends. Use screened cable for sensitive signal lines if recommended, and maintain separation from mains to avoid interference.
• Integration with access control: The SpeedStile is a node in the security ecosystem. Map the interface points—reader locations, input triggers, lock outputs, and alarm interfaces—into a wiring and logic diagram. Implement door status feedback so the building management system knows wing position and locked/unlocked state. Define fail-safe behavior: does the wing unlock on power loss, or does it remain locked? Program and document the rationale.
• Earthing and lightning protection: Large glass and metal assemblies can accumulate charge. Ensure proper protective earthing and bonding to avoid stray currents and ensure staff safety.