64 Bit - Digi Edgeport 1 Driver Windows 10

The Digi Edgeport/1 is highly regarded as a professional-grade USB-to-serial solution, known for its stability on Windows 10 64-bit compared to cheaper consumer alternatives. While it is now considered a legacy product, official driver support remains available. Performance Review & Compatibility

Reliability: Reviewers highlight that Edgeport drivers are robust enough for mission-critical industrial systems, offering better flow control and buffering than standard Prolific or FTDI-based chips.

Persistent COM Ports: A major advantage of these drivers is the ability to lock a specific COM port number to the device, even if you plug it into a different USB port on the same PC.

Windows 10 Support: Official drivers (v6.05 and newer) fully support Windows 10 64-bit. Users report successful operation even on systems that struggle with older serial adapters. Driver Installation Guide (v6.05)

To ensure a clean setup on Windows 10, follow the official Digi installation procedure:

Do not plug in the device yet. Connecting it before the driver is installed can lead to "unrecognized device" errors.

Download and Run: Get the v6.05 driver from the Digi Support Hub. Right-click the .exe and select Run as Administrator.

Connect Device: Once the installation window disappears, plug the Edgeport/1 into your USB port. It should now enumerate correctly.

Verify: Open the Edgeport Configuration Utility (found under Digi USB in the Start Menu) to confirm the COM port assignment. Critical Troubleshooting

Legacy vs. Modern: If your device is an older "Legacy" model, ensure you are using the specific legacy driver package if v6.05 fails to recognize it.

TUSB3410 Error: If Windows identifies the device as a "TUSB3410" instead of an Edgeport, it often indicates a driver conflict or a hardware fault where the EEPROM is not being read.

USB 3.0 Compatibility: While mostly stable, some older versions of the driver had issues with USB 3.0 (blue) ports; ensure you are on v6.05 or higher to resolve these host controller conflicts.

How to install the Edgeport driver in Windows - Digi International

Digi Edgeport/1 is a high-performance USB-to-serial converter that provides instant COM port expansion for Windows 10 (64-bit) systems

. This "bump-in-the-cable" solution is frequently used in mission-critical enterprise environments like retail stations and emergency vehicles. Digi International Driver Installation for Windows 10 (64-bit)

The current supported driver version for modern Windows operating systems is Digi International Preparation device into your computer before starting the installation : Obtain the Windows driver package from the Digi Edgeport Support Page : Right-click the downloaded executable (e.g., 40002537_6.05_N.exe ) and select Run as Administrator : Click the

button. A black command window will briefly appear as drivers are loaded. Connection : Once the installation window disappears, plug the Edgeport/1

into a USB port. Windows will automatically finish the device installation Digi International Verifying Successful Installation After connecting the device, use the Edgeport Configuration Utility to ensure it is working correctly: Locate Utility Edgeport Configuration Utility Confirm Connection : The device should appear under the

tab. Double-clicking the entry will list the assigned serial (COM) ports. LED Status digi edgeport 1 driver windows 10 64 bit

: In normal idle operation, the System Status LED on the device should blink slow green Digi International Troubleshooting and Legacy Support Permissions

: Administrative rights are required for a successful installation. Direct Connection : For best results, connect the

directly to the computer's USB port rather than through a non-powered hub or extension cable Legacy Drivers

: If you have an older "Legacy" Edgeport model, you may need specific older driver versions (like v5.70), which are still available as a courtesy on the Digi Knowledge Base has been assigned to your Edgeport/1 in Device Manager?

How to install the Edgeport driver in Windows - Digi International

For a Digi Edgeport/1 on Windows 10 (64-bit), the current recommended driver version is v6.05. This driver is compatible with both modern and legacy Edgeport models and is designed to install seamlessly on Windows 10. Download and Installation

Download the Driver: You can find the Edgeport Drivers on the official Digi Support site.

Run as Administrator: Right-click the downloaded installer (e.g., 40002537_6.05_N.exe) and select Run as Administrator.

Install First, Plug Later: Do not plug the Edgeport device into the USB port until after you have run the installer and the installation window has closed.

Connect Device: Once the installation is complete, plug in the Edgeport/1. Windows should automatically finalize the driver assignment. Verifying Installation To ensure the driver is working correctly:

Open the Edgeport Configuration Utility from the "Digi USB" or "Inside Out Networks" program group in your Start menu. Confirm the device appears under the General tab.

The 64-bit utility file is specifically named edgeport64.exe and is located in the \system32\ folder. Troubleshooting Tips

Legacy Devices: If you have an older "Legacy" Edgeport model, you may need version 5.70, though 6.05 typically supports both.

USB 3.0: Ensure you are using the latest driver version (6.05 or higher), as earlier versions had known issues enumerating correctly when attached to USB 3.0 ports.

Status Light: A slow-blinking green LED on the device indicates it is installed correctly and idle.

How to install the Edgeport driver in Windows - Digi International

Setting up a Digi Edgeport/1 on a modern Windows 10 64-bit system is straightforward, provided you follow the specific installation order required by Digi’s hardware. Quick Setup Guide: Digi Edgeport/1 for Windows 10 1. Download the Correct Driver

The most current driver for the Edgeport family is Version 6.05, which officially supports Windows 10 and Windows 11 (both 32-bit and 64-bit). The Digi Edgeport/1 is highly regarded as a

Official Source: You can find the latest software on the Digi Edgeport Support Page.

File to Look For: The installer is typically named 40002537_6.05_N.exe. 2. Critical Installation Steps

To avoid common "driver not found" errors, follow this exact sequence:

Unplug the Edgeport: Do NOT have the device plugged into your USB port when you start.

Run as Administrator: Right-click the downloaded .exe and select Run as Administrator.

Execute Setup: Click the Setup button. A black command window will appear briefly during the process.

Connect the Hardware: Only after the installation window disappears should you plug the Edgeport into your USB port. Windows will then automatically finish the driver binding. 3. Verifying the Connection

Once installed, you can manage your new COM port via the Edgeport Configuration Utility: Open the Start Menu and look for the Digi USB folder. Launch the Edgeport Configuration Utility.

Your device should appear under the General tab. Double-click it to see the assigned COM port number (e.g., COM3). Troubleshooting Tips LED Status: A slow blinking Green light on the Edgeport indicates it is installed correctly and idle.

Legacy Drivers: If you are using a very old "Legacy" model, you may need to check the Digi Knowledge Base for specific older revisions, though v6.05 is highly compatible with most units. USB Hubs: For the most stable connection, plug the Edgeport

directly into the computer’s USB port rather than an unpowered hub.

Need to connect multiple devices?If you're expanding beyond a single port, retailers like CDW and PCNation carry the full Edgeport line, including 4-port and 8-port industrial models.

What specific serial device are you connecting? (e.g., a GPS unit, barcode scanner, or PLC?) I can provide the exact terminal settings or pinout info if you need it.

How to install the Edgeport driver in Windows - Digi International

I couldn’t find an official Digi Edgeport/1 driver directly in this conversation, but here’s how you can get it for Windows 10 64-bit:

Part 5: Troubleshooting Common Windows 10 64-Bit Errors

Even with the correct driver, issues arise. Here is the most frequent error log.

Error #1: "The driver is not intended for this platform" (or Code 10)

Error #4: COM port disappears after Sleep/Hibernate

Troubleshooting Common Issues

1. "The driver is not signed" / Digital Signature Error If Windows 10 blocks the driver because it lacks a digital signature (common with very old legacy drivers):

2. Device Not Detected

3. COM Port Number too High Some legacy software cannot access COM ports numbered higher than 8 or 9.

To install the Digi Edgeport/1 Windows 10 64-bit , you should use the latest driver package (typically version 6.x) available from the official Digi Support Resources Digi International Installation Steps : Obtain the latest Windows driver from the Digi International support page Pre-Installation

: Disconnect the Edgeport/1 from your PC before starting the installation. Run Installer : Execute the downloaded file (e.g., a self-extracting ). It typically extracts files to C:\edgeport drivers and launches a command-prompt setup. Connect Device

: Plug the Edgeport/1 into a USB port after the driver installation is complete. Windows should then automatically detect the device and assign COM ports. : Open the Edgeport Configuration Utility

(located in the "Digi USB" program group) to confirm the device is listed and serial ports are active. Digi International Key Specifications & Troubleshooting Digi Edgeport USB-to-Serial Converters Support Resources

Contact Information. 1-877-912-3444 952-912-3444 Contact Digi sales. Digi International

How to install the Edgeport driver in Windows - Digi International

The Digi Edgeport/1 remains a robust solution for adding high-speed serial connectivity to modern systems via USB. While many legacy hardware components struggle with modern operating systems, the Edgeport/1

is fully compatible with Windows 10 64-bit using the latest drivers from Digi International. Essential Driver Information

To ensure stable operation on a 64-bit architecture, you must use the correct driver version. The most current and widely recommended version for Windows 10 is v6.05. Driver Version: 6.05 (latest)

Filename: 40002537_6.05_N.exe (or similar depending on the exact sub-version) Developer: Digi International Official Support Step-by-Step Installation Guide

Installing the Edgeport driver requires a specific sequence to avoid hardware recognition errors. 1. Preparation Disconnect the Device: Do NOT plug the Go to product viewer dialog for this item. into your USB port before the software is installed.

Administrator Rights: Ensure you are logged in with administrative privileges. 2. Installation Process

Download: Get the v6.05 driver from the Digi Edgeport Support Page.

Run Installer: Right-click the downloaded .exe file and select Run as Administrator. Setup:

Click the Setup button. A black command-line window will appear while the drivers are registered; wait for it to close automatically. Connect Hardware: Once the installer finishes, plug the Edgeport/1

into an available USB port. Windows will now automatically detect the device and assign a COM port. 3. Verification To confirm the installation was successful:

Open the Start Menu and navigate to the Digi USB program group. Launch the Edgeport Configuration Utility Edgeport/1 Cause: You installed a 32-bit driver on a 64-bit OS

should appear under the General tab with its assigned COM port listed. Optimizing for Windows 10 64-bit

How to install the Edgeport driver in Windows | Digi International