Setting up the Bematech LR2000 on Windows 10 is a straightforward process, though it requires specific drivers provided by Logic Controls, the parent company. This high-performance thermal printer supports multiple connection types, including USB, Serial, and Ethernet (on the LR2000E model). Logic Controls 1. Official Driver Download For a standard Windows 10 setup, you typically need the Windows Spooler Driver Official Source : Visit the Logic Controls Product Drivers page to find the LR2000 section. Spooler Selection : Choose either the Windows 32-bit Windows 64-bit Spooler
based on your system architecture. Most modern Windows 10 machines will use the 64-bit version. Alternative Drivers
: If you are using specific POS software, you may alternatively need the OPOS Driver Linux Driver also listed on that page. Logic Controls 2. Hardware Connection Steps
Before running the installer, ensure the printer is physically ready:
: Plug the 3-pin power cord into the back of the printer and the other end into a wall outlet.
: Connect the USB Type B (square end) to the printer and the USB Type A (flat end) to an available port on your computer.
: Load a standard 80mm (79.5mm) thermal paper roll, ensuring the paper feeds from the bottom. bematech lr2000 driver windows 10
: Toggle the power switch located on the left side of the printer. 3. Driver Installation Procedure
Once the hardware is connected and the driver file is downloaded: LR2000 POS Thermal Printer - Logic Controls
It sounds like you’re referring to an interesting post about the Bematech LR2000 (a popular Brazilian receipt/EPSON-compatible printer) and getting it to work on Windows 10.
Since I can’t see the specific post you’re referencing, here’s a breakdown of what that post likely covers—and how to solve the most common LR2000 + Windows 10 issues.
Leave a comment with:
winver)We reply within 24 hours.
Related Articles:
This article is human-written, independently researched, and updated for 2025. Not sponsored by Bematech/Elgin.
Here are a few options for a social media post or forum thread, depending on where you intend to post it.
Last Updated: October 2025
Target OS: Windows 10 (32-bit & 64-bit)
Device: Bematech LR2000 (Linha Rubi 2000) – Epson Emulation / Proprietary
If you run a retail store, restaurant, or any Point of Sale (POS) system in Latin America (especially Brazil), you are likely familiar with the Bematech LR2000. This rugged, reliable printer is a workhorse for fiscal receipts and kitchen orders. However, as technology evolves, a major challenge has emerged: Installing the Bematech LR2000 driver on Windows 10.
Microsoft has drastically changed its driver architecture since Windows 7 and XP. Older Bematech drivers (designed for Windows 98/XP) often fail to install, throw "Digital Signature" errors, or simply refuse to print. This guide will walk you through every method—from official solutions to advanced workarounds. Setting up the Bematech LR2000 on Windows 10
If you use the LR2000 in a commercial environment with Windows 10:
| Error Message | Solution |
| :--- | :--- |
| "Driver is not digitally signed" | Disable Driver Signature Enforcement (Method 1, Step 2) permanently via bcdedit /set testsigning on (advanced users only). |
| Printer prints garbage characters | You are in Bematech mode but sent Epson commands. Change emulation (Method 2, Step 1) or install correct driver. |
| "Error - Paper Out" but paper is loaded | Sensor misalignment. Clean the paper sensor with compressed air. In driver settings, disable "Paper Out reporting". |
| USB device not recognized | Bad USB-to-Parallel chipset. Buy an adapter with CH340 or PL2305 chipset, not generic ones. |
| Printing is extremely slow | Go to Printer Properties > Advanced > (Disable "Start printing after last page is spooled"). Or enable Raw printing. |
| Windows 10 update broke the driver | Uninstall the driver, roll back Windows Update (KB500xxxx), reinstall using Method 2 (Epson Generic). |
Symptoms: The printer outputs random symbols, blank receipts, or vertical lines. Solutions:
The Bematech LR2000 label printer is a popular choice among businesses that require high-quality label printing. Its compatibility with various software systems and ease of use make it a preferred device for many. However, to ensure seamless communication between the printer and a Windows 10 computer, users need to install the correct drivers.
Now that the driver is installed, you must adjust the settings for receipt printing.
Settings > Devices > Printers & Scanners.Manage.Printer properties (not "Printing preferences").80 x 297 mm (or your receipt paper size). If not listed, create a custom form.
Print Server Properties (from the same Printers & Scanners window, click on "Print Server Properties" in the blue bar).Create a new form.8.00cm and Height to 29.70cm. Save.Device Settings tab (if available), ensure "Paper Type" is set to "Thermal" and "Cutting" is enabled if your POS software supports it.Most PCs lack a physical LPT port. Use a USB-to-Parallel adapter (e.g., Cables-to-Go, Startech). Windows will assign a USB-to-parallel converter a LPT-like name (e.g., USB001). In the Ports tab, map the printer to that USB virtual port, not LPT1. Your Windows 10 build (run winver ) Connection
Clker.com is owned by Rolera LLC, 2270 Route 30, Oswego, IL 60543 support\at\clker\dot\com
