Jump to Content
Talk to an expert
Talk to an expert

Asolid Usb Mptool Verified May 2026

The ASolid USB MPTool (Mass Production Tool) is a high-level repair utility specifically for USB flash drives using ASolid controllers, such as the AS2102 or AS2115. It is designed for low-level recovery when standard Windows formatting fails. Summary Review

The tool is highly effective for "resurrecting" dead hardware, but it is not intended for casual users due to its technical complexity and the risk of permanent data loss.

Primary Use Case: Fixing "No Media," "Write Protected," or "Insert Disk" errors that software like chkdsk cannot handle. Key Capabilities:

Firmware Re-flashing: It can reprogram the microcontroller if the firmware is corrupted.

Bad Block Management: Identifies and maps out physically damaged sectors of the NAND memory.

Low-Level Formatting: Resets the drive to factory-like conditions, often recovering the original capacity or creating a stable, smaller partition. Pros & Cons Pros Cons

High Success Rate: Often the only way to fix drives that Windows won't recognize.

Destructive: Guaranteed to erase all data on the drive; use data recovery first if possible.

Official Hardware Support: Developed for specific ASolid NAND controllers.

Hard to Find: Official downloads are often restricted; users often rely on third-party sites like usbdev.ru.

Granular Control: Allows editing of Vendor ID (VID) and Product ID (PID).

Risk of Bricking: Incorrect settings can permanently disable the USB drive. Usage Tips for Verification

Identify the Controller: Before downloading, use a tool like ChipGenius to verify that your USB drive actually uses an ASolid controller.

Match Versioning: You must match the MPTool version to your specific controller model (e.g., AS2102) and flash memory type.

Run as Administrator: These tools require low-level system access to interface with the hardware. asolid usb mptool verified

Environment: If it fails on modern systems, try running it in Windows 7 or XP compatibility mode, as many of these tools were built for older OS environments.

An ASolid USB MPTool is a low-level "Mass Production" software used to manage, repair, and format USB flash drives using ASolid controllers. These tools are typically meant for manufacturers but are often used by technicians to "unbrick" drives that show errors like "No Media" or "Write Protected". Core Features

Low-Level Formatting: Unlike standard Windows formatting, this performs a deep reset of the NAND flash memory, which can resolve "Write Protection" or "Disk is Read Only" errors.

Bad Block Management: Scans the flash memory for physically damaged cells ("bad blocks") and marks them as unusable to prevent data corruption.

Capacity Restoration: Can fix "Fake Capacity" drives (e.g., a drive advertised as 64GB that is actually 8GB) by resetting the controller to recognize the true NAND size.

Firmware Reflashing: Allows you to update or reinstall the USB controller’s firmware if it has become corrupted.

Hardware Identification: Displays detailed internal hardware info, including the Flash ID (FID), Controller Model (e.g., AS3257), and NAND manufacturer.

Partition Management: Enables the creation of "Read-Only" (CD-ROM) partitions or hidden secure partitions.

VID/PID Configuration: Allows users to manually set the Vendor ID (VID) and Product ID (PID) codes, which help computers identify the device. Critical Usage Notes

Caution: Using an MPTool will permanently erase all data on the drive.

Identification: Before using an MPTool, you must identify your specific controller using a tool like ChipGenius to ensure you have the correct version for your ASolid chip.

Security: Be wary of downloading these tools from unofficial sources, as they are sometimes flagged by antivirus software or can contain malware.

The ASolid USB MPTool (Mass Production Tool) is a specialized low-level utility developed by ASolid Technology for managing, repairing, and manufacturing USB flash drives equipped with ASolid controllers. This "verified" status generally refers to versions confirmed by the community to work for specific controller-memory combinations. Core Functions & Use Cases

The tool is primarily used for deep-level hardware intervention when standard Windows formatting fails: The ASolid USB MPTool (Mass Production Tool) is

"No Media" Recovery: Fixes drives that show up in Disk Management but cannot be accessed or formatted.

Firmware Reflashing: Reinstalls the drive's internal control software to fix corruption.

Bad Block Management: Scans the NAND memory chip, identifies failing sectors, and marks them as unusable to restore drive stability.

Partition Manipulation: Can create unique partitions, such as a CD-ROM partition or an emulated floppy drive.

Device Identification: Configures Vendor IDs (VID) and Product IDs (PID) for the device. Supported Hardware

ASolid MPTools are strictly controller-specific. They are commonly used with: Controllers: AS3257ENLT, AS3257H, and AS3255 series.

Memory Compatibility: Supports various NAND types including SLC, MLC, and TLC from major manufacturers like Samsung, SK Hynix, and Toshiba. Common Troubleshooting for Windows 10/11

Users often encounter the error "93.00 is not a valid floating point value" when launching the tool on modern Windows versions. Verified community fixes include:

Delete the default.ini file in the tool's folder and manually fill in settings.

Change Regional Settings: In Windows settings, change the "Decimal symbol" from a comma (,) to a period (.).

Password Access: The default password for unlocking advanced settings in ASolid tools is often 0000. Safe Usage Guide

Warning: Using an MPTool will permanently erase all data on the drive.

Identify Your Controller: Use a tool like ChipGenius to find your specific ASolid controller model, VID, and PID.

Match the Tool: Download the exact version of the ASolid MPTool that supports your specific controller and flash memory ID. Extract the verified tool to a folder on your desktop (e

Set to "Test Mode": If the drive is not detected, it may need to be put into a physical "test mode" by shorting pins (only for advanced users).

Phase 1: Driver Installation (The Tricky Part)

  1. Extract the verified tool to a folder on your desktop (e.g., C:\AlcorMP_Verified).
  2. Run LoadDriver.exe as Administrator.
  3. Click "Install" – Windows may show a warning about unsigned drivers. Choose "Install this driver software anyway."
  4. Confirm that "Alcor Micro USB Mass Production Tool Driver" appears in Device Manager under "Storage controllers."

Q: Is there a Linux or macOS version?

A: No. MPTOOLs are Windows-only due to direct USB low-level access. Use Wine with USB passthrough (experimental, not verified).

Getting Started — Step-by-Step (Assumes Windows + Admin)

  1. Identify the controller

    • Plug in the USB drive and open Device Manager > Disk drives / Universal Serial Bus controllers.
    • Note vendor/product IDs (VID:PID) and any device strings.
    • Use tools like ChipGenius, Flash Drive Information Extractor, or USBDeview to determine controller model and NAND type.

  2. Obtain correct MPTool and firmware

    • Locate an MPTool version that supports your controller model.
    • Obtain the exact firmware binary for the controller/NAND combination.
    • Verify checksums if provided.

  3. Install drivers

    • Install required low-level driver (often WinUSB or a vendor driver).
    • Reconnect the USB drive; ensure it's visible to the MPTool (some tools show device in a dropdown).

  4. Backup and precautions

    • If possible, read and save device parameters or a full dump of the flash.
    • Document current VID/PID, serial strings, and capacity.

  5. Common operations in MPTool

    • Read/Identify: Retrieve controller info, firmware version, and NAND details.
    • Read Flash / Dump: Extract full flash contents to a file for backup.
    • Format / Low-level format: Reinitialize flash structures.
    • Write Firmware / Upgrade: Flash new firmware binary to the controller.
    • Set VID/PID / Strings: Modify identification strings if supported.
    • Repair / Rebuild: Fix partition tables, fake capacity corrections, or remap bad-block tables.

  6. Verifying success

    • After operations, safely remove and reinsert the drive.
    • Check Windows Disk Management for correct capacity and partitions.
    • Use read/write tests (e.g., H2testw, F3) to verify usable capacity and detect fake-size issues.

AStep-by-Step Guide: How to Use the ASolid USB MPTOOL (Verified & Safe)

If you have a cheap or unbranded USB flash drive that suddenly shows "0 bytes," won't format, or has disappeared from File Explorer, you’ve likely encountered a controller firmware failure.

The good news? If your drive uses an ASolid controller (common in budget drives from AliExpress, Amazon, or generic brands), the ASolid USB MPTOOL (Mass Production Tool) can bring it back to life.

Warning: This tool is powerful. It low-level formats your drive and permanently erases all data. Use it only to repair dead drives or restore them to factory settings.

Q: My drive is from Sandisk – will it work?

A: Sandisk often uses proprietary controllers, not ASolid. Verify with ChipGenius first.

Step 1: Identify Your ASolid Controller First

Before downloading, open your USB drive and check the Chip Part Number using:

Look for something like:
VID_1234 PID_5678 → Controller: ASolid AU89102AA

Write this down. You need the exact controller version.